Everyone has a bathtub in the bathroom, so that when you take a shower, you can not only clean but also enjoy the time sitting in the bathtub. For the bathtub, it will take a long time to use and it will be damaged after a long time of use. In the general knowledge of everyone, if there is a mistake, it will be repaired immediately, and the repair of the cast iron bathtub is a technical activity. Then everyone will follow the small series to see the exciting content of the cast iron bathtub repair .
First, the cleaning of the bathtub:
1. Use a mild treatment for the bathtub. The stain on the surface of the bathtub should be washed with a soft plastic brush and bleaching powder to remove stains and eliminate virus mold. There is also a way to remove the stain from the lemon, especially for stubborn stains, you can use a half of lemon and salt to rub hard, or you can use a soft toothbrush to rub the toothpaste.
2. It is also possible to use turpentine.
3. Lemon and white vinegar works better, but the taste is heavier.
4. The cast iron bathtub should be thoroughly rinsed with clean water after each use and dried with a soft cloth. If you encounter stubborn stains, use a small amount of abrasive cleaner to clean. Clean the bottom non-slip surface with a soft nylon brush. Do not scrub with a steel ball, wire brush or abrasive sponge. The jacuzzi system should be flushed twice a month. Adjust the nozzle clockwise to the fully closed position to prevent air leaks.
5. After each use, do not rush to let the water inside, leave the water in the bathtub, add a small amount of detergent and household bleach. Drain the bathtub and drain the water. When the bathtub is in a hot and humid state for a long time, it will also breed a lot of bacteria. Sometimes it is cleaned and the surface looks clean. In fact, there are still many bacteria.
It is best to rinse the surface of the bathtub with boiling water frequently. Do not use disinfectant water casually, because disinfecting water does not necessarily kill mold and fungi.
Second, the repair of the bathtub
If the home is an acrylic bathtub, accidentally touch the crack when using it, and use the super glue to bond the crack in time. When bonding, it is best to combine the two people, first clean the cracks, then force the two parts to align, use a good glue to slowly inject glue along the cracks in the bathtub, in the process of continuous use of drugs An object such as a hammer taps the cylinder gently, so that the glue is poured into the crack as much as possible.
Remove the glue from the docking station until it is loose. After sticking, use a little AB glue and some talcum powder to make a paste in it, gently wipe it on the crack, and smooth it as much as possible. After it has dried, gently grind it with water sandpaper and a little water.
After the glue has dried, adjust the paint mixture with the color of the bathtub to be thinner, dilute it a little, apply it to the repaired area, and finally apply a layer of varnish. If it is scratched, you can use different types of sandpaper for sanding. Sandpaper should be sanded in one direction. Then polish it again.
For bathtubs with heavy injuries, don't move easily. It is best to contact a professional. Do not hit or hit the surface with a hard object, causing bruises or scratches. Clean the pipe at any time to prevent clogging. It is best to clean it once or twice a week to remove the taste and prevent bacterial growth.
You can use a product that cleans the sewers and pour it into the sewer. After 5 minutes, it should be cleaned. Be careful not to use it in metal pipes. If the bathtub is blocked, first close the water removal valve, then put a proper amount of tap water in the bathtub; place the rubber suction device (to clear the toilet) on the water removal valve; while opening the water removal valve, suffocate the basin or The overflow hole of the bathtub; then quickly attracting up and down, sucking out the dirt or hair and cleaning it off in time. In the case of a serious blockage, it can be repeated several times until the dredge is clean.
How about, I saw the wonderful introduction to the repair of the cast iron bathtub. Did you know a lot about the repair of cast iron bathtubs? I hope that you can learn more about home improvement knowledge through this article, and you will be able to create a more perfect home environment. Thank you for reading this article and your support and love for Xiaobian. If you want to get more information about home improvement, please continue to pay attention to the decoration home network.
More related wonderful reading:
Advantages and disadvantages of cast iron bathtub, installation method of cast iron bathtub
What are the advantages and disadvantages of cast iron bathtubs? How to choose a cast iron bathtub?
1. Description of M mddium duty slurry pump
Naipu NP-M series centrifugal slurry pumps and spare parts could fully interchange with world famous brand.These pumps are of heavy-duty construction, designed for continuous pumping of highly abrasive and corrosive slurries. They feature a wide choice of replaceable abrasion resistant metal casting liners and Impellers, which are all interchangeable within a common casting assembly.
Typical Applications---
Dense media transfer
Dense media make-up
Bottom boiler and fly ash
Ferrosilicon make up
Thickener underflow
Dewatering
2.Construction drawing of M medium duty slurry pump
Main Part Number At The Drawing
032:Frame Plate
132:Discharge Joint
110:Volute Liner
041:Frame Plate Liner Insert
124: Volute Cover Seal
122: Stuffing Box Seal
147:Impeller
013:Cover Plate
083:Throat bush
060: Intake Joint
Material of Construction
LINERS
IMPELLERS
CASING
BASE
EXPELLER
EXPELLER RING
SHAFT SLEEVE
SEALS
Standard
Chrome Alloy
Chrome Alloy
SG Iron
SG Iron
Chrome Alloy
Chrome Alloy
SG Iron
Rubber
or
SG Iron
or
SG Iron
3.M Medium duty slurry pump select Chart
M Medium Duty Slurry Pump,Heavy Duty Slurry Pump,Warman Slurry Pump,Medium Duty Slurry Pump
Shijiazhuang Naipu Pump Co., Ltd. , https://www.naipu-pump.com