The following article is about "The cause of the non-operation of the feed-in plant's small 2-6 ton biomass boiler boiler bag filter straight-through electromagnetic pulse valve" article by Botou City Chunhui Environmental Protection Equipment Co., Ltd., declined to be reproduced, if you want to know more about the selection of the filter Type, you can call our professional telephone manager to consult, qq 3406358895. We have many years of experience in the selection of precipitator equipment, and will design, produce, install, and after-sales professional solutions based on your operating conditions.
Feed Plant Small 2-6 Ton Biomass Boiler Bag Dust Collector Feedthrough electromagnetic pulse valve is an important component of the blowing mechanism. It is mainly used to control the compressed air blown into the bag control switch. Its performance is good or bad. Affect the bag filter dust removal effect. Therefore, when the customer encounters the bag filter pulse solenoid valve does not work, how to deal with it?
Cause the bag filter pulse solenoid valve does not work we can find from the following points:
1. Check if the wiring of the power supply is good. If it is not connected, reconnect it. The power supply voltage is not within the operating range and must be adjusted to the normal operating range.
2. Check if there is any problem with the coil of the solenoid valve, for example, when the welding is disconnected or a short circuit occurs. In this case, replace the coil in time.
3. When the bag filter is opened, the electrical signal disappears, and the leading column cannot be reset. There are burrs or impurities, etc., so that moving the column stuck; spring fatigue, lack of elasticity; damping hole plugging, then we must check whether the air bag pressure is too low or too much pressure gas.
4. Close the valve in front of the pulse valve airbag, disassemble the pulse valve, and see if the diaphragm has any damage. If it is damaged, replace the new diaphragm in time.
5, look at the diaphragm gasket and the outlet port surface there is no foreign matter, so that the two can not be closely integrated, leading to the phenomenon of leakage of pulsed electromagnetic valve, which is to open the solenoid valve, remove the clean foreign body. When the customer installs the bag filter, in order to avoid the blockage of rust, welding slag and other debris and cause the solenoid valve does not work, it must be vented to blow the compressed air pipe to remove debris.
6. Check if there is any leakage in the blowing tube in the air bag. Its air leakage will also cause the compressed air to directly enter the blowing tube without passing through the solenoid valve. The solenoid valve will not work. We must replace it in time.
7. Check if the pulsed solenoid valve has reached the age of use or the frequency of use is too high. This will require replacement of the new product.
The above is a few ways to handle the bag filter pulse solenoid valve when it is not working. Hopefully it will help everyone. If the above method can not be solved, please call Chunhui Environmental Protection. We will help you solve it.
Feed Plant Small 2-6 Ton Biomass Boiler Bag Dust Collector Feedthrough electromagnetic pulse valve is an important component of the blowing mechanism. It is mainly used to control the compressed air blown into the bag control switch. Its performance is good or bad. Affect the bag filter dust removal effect. Therefore, when the customer encounters the bag filter pulse solenoid valve does not work, how to deal with it?
Cause the bag filter pulse solenoid valve does not work we can find from the following points:
1. Check if the wiring of the power supply is good. If it is not connected, reconnect it. The power supply voltage is not within the operating range and must be adjusted to the normal operating range.
2. Check if there is any problem with the coil of the solenoid valve, for example, when the welding is disconnected or a short circuit occurs. In this case, replace the coil in time.
3. When the bag filter is opened, the electrical signal disappears, and the leading column cannot be reset. There are burrs or impurities, etc., so that moving the column stuck; spring fatigue, lack of elasticity; damping hole plugging, then we must check whether the air bag pressure is too low or too much pressure gas.
4. Close the valve in front of the pulse valve airbag, disassemble the pulse valve, and see if the diaphragm has any damage. If it is damaged, replace the new diaphragm in time.
5, look at the diaphragm gasket and the outlet port surface there is no foreign matter, so that the two can not be closely integrated, leading to the phenomenon of leakage of pulsed electromagnetic valve, which is to open the solenoid valve, remove the clean foreign body. When the customer installs the bag filter, in order to avoid the blockage of rust, welding slag and other debris and cause the solenoid valve does not work, it must be vented to blow the compressed air pipe to remove debris.
6. Check if there is any leakage in the blowing tube in the air bag. Its air leakage will also cause the compressed air to directly enter the blowing tube without passing through the solenoid valve. The solenoid valve will not work. We must replace it in time.
7. Check if the pulsed solenoid valve has reached the age of use or the frequency of use is too high. This will require replacement of the new product.
The above is a few ways to handle the bag filter pulse solenoid valve when it is not working. Hopefully it will help everyone. If the above method can not be solved, please call Chunhui Environmental Protection. We will help you solve it.
Tap Set,Cobalt Tap Set,Drill Tap Bits,Drill Tap Bits Set
Danyang Yongshun Tools Co.,Ltd , https://www.china-drill-bit.com