Q: Can I use the same connector to connect cables that are not listed in the table of connector matching cables as long as they are close in size?
Answer: No. Although the connection installation itself may be feasible, the quality of the connection may be seriously affected. Although the connection seems to work, some factors such as the stability of the appliance, weak cable connection, and other factors may cause problems in practical use. Therefore, these unlisted cables must be tested and evaluated to determine if the connectors can be matched. When using crimp-type connectors, this problem should be paid special attention.
Q: What is the cable connection strength?
Answer: The cable connection strength refers to the maximum load that the cable can bear when it is pulled out of the connector by tensile stress. For Canare's products, “cable connection strength†refers to the strength of the cable's outer conductor, excluding the connection strength of the center contact and the inner conductor.
Q: Is there a directionality in the crimp tailpipe?
A: For stepless (straight) tailpipes of BCP-C3B or similar BNCs, the direction of the tailpipe during installation is irrelevant. For one end of the BCP-C5FA or other tail pipe, there is a slope (Cao line), and the tail pipe is also installed with no direction. However, for trailing tailpipes, tailpipes such as BCP-C1 are directional.
Q: How do I handle aluminum foil for coaxial cables with aluminum foil shielding?
A: If the aluminum foil is not very sticky, the exposed aluminum foil should be completely stripped. If the aluminum foil adheres to the insulator and stands firmly, make sure that the conductor at the cut end of the insulator and the debris of the aluminum foil are cleaned, because the debris may cause a short circuit.
Q: Why do some other company's connectors have sophisticated central stylus? Do these BNC connectors match Canon's BNC sockets?
A: The BNC with a pointed center pin conforms to the 50 JIS standard. The Canon America BNC's central stylus meets the military standard (MIL standard) and is therefore not tipped. In two different ways, there is no direct effect on the quality of contact. The actual contact surface of Canon America BNC connector is consistent with the standard, so there is no compatibility problem.
YC had established the post-doctoral research station
since 2006 focusing on new material development such as P92, P91, X80. More
than 29 kinds of new materials and products have won the national and
provincial prizes from 2006 till now.
Answer: No. Although the connection installation itself may be feasible, the quality of the connection may be seriously affected. Although the connection seems to work, some factors such as the stability of the appliance, weak cable connection, and other factors may cause problems in practical use. Therefore, these unlisted cables must be tested and evaluated to determine if the connectors can be matched. When using crimp-type connectors, this problem should be paid special attention.
Q: What is the cable connection strength?
Answer: The cable connection strength refers to the maximum load that the cable can bear when it is pulled out of the connector by tensile stress. For Canare's products, “cable connection strength†refers to the strength of the cable's outer conductor, excluding the connection strength of the center contact and the inner conductor.
Q: Is there a directionality in the crimp tailpipe?
A: For stepless (straight) tailpipes of BCP-C3B or similar BNCs, the direction of the tailpipe during installation is irrelevant. For one end of the BCP-C5FA or other tail pipe, there is a slope (Cao line), and the tail pipe is also installed with no direction. However, for trailing tailpipes, tailpipes such as BCP-C1 are directional.
Q: How do I handle aluminum foil for coaxial cables with aluminum foil shielding?
A: If the aluminum foil is not very sticky, the exposed aluminum foil should be completely stripped. If the aluminum foil adheres to the insulator and stands firmly, make sure that the conductor at the cut end of the insulator and the debris of the aluminum foil are cleaned, because the debris may cause a short circuit.
Q: Why do some other company's connectors have sophisticated central stylus? Do these BNC connectors match Canon's BNC sockets?
A: The BNC with a pointed center pin conforms to the 50 JIS standard. The Canon America BNC's central stylus meets the military standard (MIL standard) and is therefore not tipped. In two different ways, there is no direct effect on the quality of contact. The actual contact surface of Canon America BNC connector is consistent with the standard, so there is no compatibility problem.
We can produce lots of Alloy Steel Pipe that used on the Petrochemical and Refinery project, such as the P11 Steel Pipe ,P12 steel pipe ,P22 steel pipe ,P91 steel pipe,P92 steel pipe ,P5 steel pipe, P9 steel pipe and P36 steel pipe.From 2013 to 2015 year, we awarded the world`s largest P91 order from Reliance (single PO 8,000 tons P91), the final additional quantity together is up to 16,000 tons, Plus CS 11000 tons. Entire projects P grades are from Yangzhou Chengde. Our main reference list on the Petrochemical and Refinery projects as following:
| EPC | Owner | Project name | Location | Project introduction | Material | Size range(mm) | Qty(MT) |
| Flour/Technip | Sasol | Lake Charles Chemical complex | Lousiana USA | Sasol's Lake Charles Chemical Complex is a world-scale petrochemical complex The $8.9 billion project will roughly triple the company's chemical production capacity in the U.S. and enable it to build on its strong positions in robust and growing chemicals markets. | GR6/P22/P91 | 114~609*14.27~46.99 | 600 |
| Flour/Bechtel | Reliance | Jamnagar Refining And Petrochemical Complex | Gujarat India | The Jamnagar complex comprises of a petroleum refinery and associated petrochemical plants. The refinery is equipped to refine various types of crude oil (sour crude, sweet crude or a mixture of both) and manufactures various grades of fuel from motor gasoline to Aviation Turbine Fuel (ATF). The petrochemicals plants produces plastics and fibre intermediates. | A106B/P11/P5/P9/P91 | 21.3~1066.8*4.78~60.33 | 25,370 |
Oil Pipe,Refinery Pipe,Astm A519 Pipe,Fuel Refinery Pipe
YANGZHOU CHENGDE STEEL PIPE CO.,LTD , https://www.chengdepipe.com