With the pursuit of high quality of life, there have been a variety of decorative building materials on the market. Among them, natural culture stone is one of them. Its material is very high-end, with rich and colorful color lines, and it is deeply loved by people nowadays. The following small series introduces the natural cultural stone installation method and natural cultural stone classification.
Natural culture stone installation method
1. Clean the wall surface and make a rough surface. (If it is a low-absorption smooth surface such as plastic wood, it must be covered with barbed wire, and make a rough bottom, fully re-applied after the health
2. Before putting the rock on the rock, be sure to arrange the rock on the flat ground and put it in the best order and then lay it out in an orderly manner. (The rocks with similar size, shape and color should not be adjacent to each other). The sequence of the cement layer - the cultural stone layer - the cement adhesive seam layer should be followed.
No. 3,425 or more white cement, ordinary cement (cement: sand: 801 glue ratio of 1:2:0.03), ceramic adhesive (note the use of adhesives) high-performance special adhesive can be used as glue. The order of bonding is: cultural stone - cement tank (increased bond strength) - adhesive.
4. Fully infiltrate the rock. Apply adhesive at the center of the rock bottom to form a mountain shape (When the antique brick is attached, the bottom of the brick can be coated with a thin layer of adhesive.) If the surface is dirty, it must be brushed in time. Use after cleaning.
5, first paste the corner. Fully pressed so that adhesive can be seen around the rock (some products do not require corners)
6. If the construction needs, can cut the rock to adjust.
7, fill the gap with plastic bags filled with paint, pay attention to grasp the depth, the deeper the gap three-dimensional effect of the product
8. After initial caking of the caulking agent, remove the excess caulking material with bamboo, etc., and repair the crevice surface with a water-soaked brush. If there is a small amount of caulking agent or adhesive on the rock surface, wait for it to dry. After removing with a brush. better. Some products do not need to leave seams.
9. When the rock is used outdoors, after it is well-laid, it should be kept for one week. After the product and caulking agent are completely dry, it can be sprayed with protective agent for protection (waterproof, antifreeze, anti-ultraviolet, anti-return alkali etc.).
Natural stone construction considerations
1. During the construction process of natural culture stone, if cement or jelly is accidentally stained, it must be cleaned immediately to prevent it from solidifying on the surface of cultural stone and it is difficult to clean it, thereby affecting the decorative effect of natural culture stone. .
2. Before the installation of natural culture stone, it is best to prepend the figure so as to avoid mistakes in the installation process, affecting the overall aesthetic coordination.
3, the installation area of ​​natural culture stone in the room can not be too large, otherwise it is easy to monotonous, unnatural room decoration effect. The natural color of the indoor natural culture stone is best to use the closest color or complementary color, so as to avoid obvious color contrast and cause uncoordinated beauty.
4. It is best not to install the culture stone of sandstone in the outdoor, so as to avoid the phenomenon of water seepage after being exposed to the wind and bring inconvenience to people's residence.
Natural stone classification
1. Rock—The natural rock has a special layered floor plan. Its grain is clear and picturesque, its texture is delicate and delicate, and its air quality is extraordinary and refined. Nature's vast seas and mulberry fields vividly show off a kind of back to nature. Emotions.
2. Sandstone—The surface and texture of sandstone have a primitive atmosphere, like the rolling dunes in the desert, like the smooth beach on the seashore. It is the perfect combination of overall harmony and detailed change. The color of sandstone is clear, white as snow and ice, yellow as fine as sand, and red as magma. It is like the steady personality that it grinds for millions of years. It is dignified and elegant.
3, rust plate --- rust plate has pink rust, rust, jade rust, purple rust and other types, beautiful colors, patterns changeable, each piece is unique. The rust plate has a warm affinity and gives a natural, original, mysterious and romantic feel in a relaxed and relaxed atmosphere.
4, tile - natural tile is the ultimate slate layered sheet, only a few millimeters thick, thin and tough. Putting a variety of tile sizes in a variety of arrangements or stacking can make the roof more three-dimensional. The combination of multiple colors can make the building more vital.
5. Mushroom twist - Mushroom stone has the shape of an ancient castle wall stone, dignified and unrestrained, rough appearance is extremely three-dimensional, giving people nostalgic feelings. Mushroom stone is carefully crafted by humans. Colors can be freely allocated and the lines can be run freely. Therefore, the overall effect is unique.
6, Yuhuashi --- natural stone collected in the riverbed, colorful, attractive texture. The artificial stone is broken by a large piece of stone machinery and then rubbed to sharpness and blunt. The color is gorgeous, and the water is more colorful. Yuhua stone beads round jade, like a note piled up a flowing architectural movement.
Editor's summary: The installation methods of natural culture stone and the classification of natural culture stone are introduced here. I hope to help everyone. If you want to know more about yourself, you can follow the information on this site.
Cultural stone natural culture stone installation method
Titanium Bars,Titanium Rod,Pure Titanium Bar,Rectangular Titanium Bars
Baoji Yongshengtai Titanium Industry Co., Ltd. , https://www.bjystititanium.com